厨房 faucet 的 fixture, 下面是个 铁片,不厚,原来是 应该用手拧的,那对螺丝是 固定的,螺丝很好拧,但铁片和上面绣住了,还薄,手完全搞不动,也使不上力,
现在是 把 新的 管子换进去,对付着用,不太 好看,
版主: QIANSHUIBA, F150
厨房 faucet 的 fixture, 下面是个 铁片,不厚,原来是 应该用手拧的,那对螺丝是 固定的,螺丝很好拧,但铁片和上面绣住了,还薄,手完全搞不动,也使不上力,
现在是 把 新的 管子换进去,对付着用,不太 好看,
cellcycle1 写了: 2025年 8月 26日 14:17厨房 faucet 的 fixture, 下面是个 铁片,不厚,原来是 应该用手拧的,那对螺丝是 固定的,螺丝很好拧,但铁片和上面绣住了,还薄,手完全搞不动,也使不上力,
现在是 把 新的 管子换进去,对付着用,不太 好看,
Use channel wrench to grip as much as possible and turn
Or, you can use a screw driver and a hammer to loosen it by striking on the side.
Spray some WD-40 first to make it easier.
Real man only needs 2 items in his toolbox: duct tape and WD40...
这明显是WD40的适用范围。。。
wildthing 写了: 2025年 8月 26日 14:20Use channel wrench to grip as much as possible and turn
Or, you can use a screw driver and a hammer to loosen it by striking on the side.
Spray some WD-40 first to make it easier.
channel wrench 试了,不行, 锤子和螺丝刀,也不行,主要是没有空间,本身还大,需要大 wrench, 还夹不住,薄
我增经试着把 螺丝放回去一半,拧一对螺丝,也不行,就是是不上劲,
macarthur 写了: 2025年 8月 26日 14:35Real man only needs 2 items in his toolbox: duct tape and WD40...
这明显是WD40的适用范围。。。
喷了好多,好多,,,
wd40
cellcycle1 写了: 2025年 8月 26日 14:35channel wrench 试了,不行, 锤子和螺丝刀,也不行,主要是没有空间,本身还大,需要大 wrench, 还夹不住,薄
我增经试着把 螺丝放回去一半,拧一对螺丝,也不行,就是是不上劲,
cellcycle1 写了: 2025年 8月 26日 14:35channel wrench 试了,不行, 锤子和螺丝刀,也不行,主要是没有空间,本身还大,需要大 wrench, 还夹不住,薄
我增经试着把 螺丝放回去一半,拧一对螺丝,也不行,就是是不上劲,
you need to remove the screws first. They are keeping the plate in place.
this doesn't work at all. there is no space most of the time. Waste of money.
cellcycle1 写了: 2025年 8月 26日 14:35channel wrench 试了,不行, 锤子和螺丝刀,也不行,主要是没有空间,本身还大,需要大 wrench, 还夹不住,薄
我增经试着把 螺丝放回去一半,拧一对螺丝,也不行,就是是不上劲,
用锥子慢慢的敲。只要松动一点点就可以了。你右边还是有不少空间的。 用个短一点的螺丝起子。
wildthing 写了: 2025年 8月 26日 14:47this doesn't work at all. there is no space most of the time. Waste of money.
如果钳子头够大,垂直夹住 圆的地方,拧? 貌似可行,